Introduction to the home automation system HDL
Technology "smart home" is designed to provide the maximum level of comfort for the owners of an apartment or house. It will help save time for doing household chores, because automation is now responsible for this, which controls and controls many household processes.
"Smart Home" - an integrated technical solution, implemented through software and hardware. These include: electricity consumers, household and technical appliances, various subsystems, engineering devices, which are combined into a single home control system.
We got into the hands of a demonstration set of the firm HDL, engaged in automated systems.
')
This device vividly demonstrates the functionality of the automation systems of the Smart Home:
You can also program various combinations of device operation due to the Logic Module.
This device is configured using the HDL-BUS software package. HDL Demo Case is connected to a computer via Ethernet or the Internet. After starting the program, a registration window will appear asking you to enter the serial number and registration code, which can be obtained by sending an email to the email address indicated there.
The figure shows the starting window of the program:
Each 1-IP Switch Board is capable of processing up to 253 devices:
After starting this program, it is required to search for devices present in our device. To begin, the address (or address range) is selected. At the end of the search, you can add the necessary devices to the workspace.
After all devices are found and added to the workspace, you can configure each of them. You can also launch the settings window for the required device by pressing the corresponding menu button:
As a result, we have a pretty good smart home system. But like everyone else, it is not without flaws. Immediately striking her great price (~ $ 2500). Program complex HDL BUS leaves much to be desired. All the study of this device was accompanied by frequent program hangs. We also could not connect to the touch screen in order to configure it (the program simply does not find it). However, I was pleased with the technical support. A couple of days after registering on the official Russian site, they called me and asked if their help was needed.
I would like to hear an objective opinion of habrayuzer on this product.
"Smart Home" - an integrated technical solution, implemented through software and hardware. These include: electricity consumers, household and technical appliances, various subsystems, engineering devices, which are combined into a single home control system.
We got into the hands of a demonstration set of the firm HDL, engaged in automated systems.
')
This device vividly demonstrates the functionality of the automation systems of the Smart Home:
- light control (5 built-in dimmable LED lamps, 8 small light bulbs on the relay channels, motion sensor functions, light sensor, lighting scenarios);
- climate control (climate pages on DLP, thermosensor on DLP, heating control through a relay, infrared control of air conditioning, climate control functions from the touch screen);
- music and video control (Z-Audio, plays music from an SD card, FM tuner or from a local input, can be connected to a computer network, IR control of devices, RS232 / RS485 control of third-party devices);
- security system (motion detection, security controller, installation of modes with DLP and touch screen), relay operation.
You can also program various combinations of device operation due to the Logic Module.
Modules
- Full list of modules:
- Power supply SB-DN-PS750
- Touchscreen display SB-WL-TS7, B
- DLP panel HDL-MPL8.48
- 8-keypad HDL-MP8B.48
- Dimmer HDL-MD0403.432
- The relay magnetic with blocking SB-DN-MR0410
- SB-CMS-12in1
- 4-pin dry contact module SB-DRY-4Z
- Climate control module HDL-MAC01.331
- Logic Controller SB-DN-Logic96
- Security Controller SB-DN-SEC250K
- Gateway for programming the HDL-BUS Pro system and remote access to the HDL-MBUS01IP.431 bus
- Power supply for Z-Audio SB-DN-PS1.2AD
- RS-C65P column
- 48 Channel DMX Scene Controller with Ethernet Port SB-DN-48DMX
- Infrared Transmitter with SB-IR-EM Switch-On Detection Sensor
- Relay to DIN rail for controlling blinds, roller shutters, curtains, gates and reversible loads SB-DN-2Motor
Detailed description of each module
It feeds about 25 devices for the automated control system HDL, no more than 2x on one
Button operation modes:
Button control options:
Timer Functions Scenarios up to 99 events. The user determines the backlight and the status of the LCD.
Free graphics in bmp format with reference to status.
4 inputs dry contacts.
Types of targets: electrical switch, mechanical switch.
Goal control modes: scene, sequence, timer, universal switch, single channel adjustment.
It is used to connect to the HDL-BUS bus classic mechanical switches and security sensors.
Relay to DIN rail to control blinds, shutters, curtains, gates and reversible loads.
Power supply SB-DN-PS750
- Power supply: AC 220V ± 10%
- Frequency: 50 ~ 60 Hz
- Bus power: 750mA
- Output voltage: DC 24V
- Operating temperature: 0 ° C ~ 45 ° C
- Operating relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Installation: standard 35mm Din-rail
- Dimensions: 72x88x66 (mm)
It feeds about 25 devices for the automated control system HDL, no more than 2x on one
Touchscreen display SB-WL-TS7, B
- Connects to the system via TCP / IP interface (RJ-45)
- built-in USB and SD-card ports
- pre-installed TouchLife software
- control of light, climate, curtains, Z-Audio, security system
- control of household devices by IR (TV, DVD)
- black glass frame
- Bus Power or PoE
- BP + 24VDC required
DLP panel HDL-MPL8.48
- Power supply: DC 24V
- Consumption: 30mA / DC 24V
- Operating temperature: 0 ° C ~ 45 ° C
- Relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Installation: standard square mounting box
- Dimensions: 86x86x21 mm
- Frame: square, European standard
- Square european style
- enlarged glass size for a full fit to the wall
- 7 dynamic pages
- Built-in IR receiver
- Thermostat
- temperature sensor
- Manage music client (display songs and playlists)
- Management of heating, air conditioning, security
- Built-in IR receiver, thermostat, temperature sensor 2-position keys (left-right, 99 commands for each side)
Button operation modes:
- One on / off, one on, one off, combination on, combination off, instantly.
Button control options:
- scene, sequence, timer, universal switch, - single channel control, scene broadcast, channel broadcast, - curtain
- page 1-4 for lighting control, other loads, - page 5 for controlling the air conditioner, - page 6 for controlling the music, - page 7 for controlling the heating
Timer Functions Scenarios up to 99 events. The user determines the backlight and the status of the LCD.
Free graphics in bmp format with reference to status.
8-keypad HDL-MP8B.48
- Power supply: DC 24V
- Consumption: 15mA / DC 24V
- Operating temperature: 0 ° C ~ 45 ° C
- Relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Installation: standard square mounting box
- Dimensions: 86x86x21 mm
- 8 buttons with double functionality (left, right)
- LED Backlight
- IR receiver (optional)
- Script support up to 99 events
- Dimming
- Double click
- Replaceable labels on buttons
Dimmer HDL-MD0403.432
- 1-phase
- Universal power supply 85-120V, 220-240V, 50-60Hz
- Size - 216x88x66 mm
- LED indication
- Consumption - 20mA
- New type of tire mounting
- Replaceable quick fuses
The relay magnetic with blocking SB-DN-MR0410
- Built-in script and sequence controller;
- Management of low-power loads (light, small motors, pumps, calls, locks, sirens, servos)
- It can work as a continuous relay
- Power supply: 10-220V
SB-CMS-12in1
- Infrared motion sensor
- Ultrasonic presence / motion sensor
- Light Sensor (LUX)
- temperature sensor
- 2 dry contact inputs
- 2 relays for connecting loads (light, fan, etc.) up to 5A each
- IR receiver: You can remotely receive up to 8 codes
- IR transmitter: You can transmit up to 99 IR codes
- Permanent control of the light level
- 4 logical operators: AND, OR, NOT-AND, NOT-OR.
- 32 logical blocks: 8 different inputs and more than 10 targets can be set
- Can control each logic block
- Can work with the security module: "SECURITY" mode
- It can be used to determine the various conditions of a controlled room
- Easy setup and selection of operating modes.
- Power supply: DC 24V
- Consumption: 150mA / DC24V
- Communication Protocol: HDL-BUS Pro Bus
- Operating temperature: 0 ° C ~ 45 ° C
- Operating relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Detection angle: 110 °
- Detection diameter: 10m
- Height adjustment: 0.3-4m
- Installation: ceiling mount
- Dimensions :: 108x34 (mm)
4-pin dry-contact input module SB-DRY-4Z
- Power supply: DC 12 ~ 30V
- Standby consumption: 20mA / DC 24V
- Communication Protocol: HDL Bus
- Operating temperature: 0 ° C ~ 45 ° C
- Operating relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Dimensions: 49x31x12 (mm)
4 inputs dry contacts.
Types of targets: electrical switch, mechanical switch.
Goal control modes: scene, sequence, timer, universal switch, single channel adjustment.
It is used to connect to the HDL-BUS bus classic mechanical switches and security sensors.
Climate control module HDL-MAC01.331
- Modes: Heat, Cool, Single Stage, Fan Low, High, Meduim, VAV 0-10V and
- Manages: Fan Coils (FCU), Air Heaters (AHU) and Servo / Valve (VAV)
- Works with DLP for climate control.
- Consumption: 95 mA
- Module size: 272x88x66 mm
Logic Controller SB-DN-Logic96
- Editable list of events for each day
- Maximum 12 modes per day
- In each mode 4 logical blocks AND, OR, NOT-AND, NOT-OR with 255 flags each can be used
- Logic inputs: Time, module status, external inputs, universal switches, etc.
- Remote programming and control function
- Built-in timer, calendar, event or reminder function
- Power supply: DC 24V
- Standby consumption: 15mA / DC24V
- Operating temperature: 0 ° C ~ 45 ° C
- Operating relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Installation: Standard 35mm Din-rail
- Dimensions: 72x88x66 (mm)
Security Controller SB-DN-SEC250K
- Supports up to 250,000 address zones (HDL sensors or connected to the HDL bus via dry contact inputs)
- 24-hour zones, fire, gas, panic, silent siren, alarm lock
- Automatic installation and disarming
- Sensor types: NC, NO, analog
- Dials SMS and sends an alarm
- 8 global zones / objects
- Mimics presence
- Security modes: no home, night, night with guest, day, vacation, off and others set from keypads and touch screens
- Built-in enhanced security logic and interoperability with other systems
Gateway for programming the HDL-BUS Pro system and remote access to the HDL-MBUS01IP.431 bus
- DIN rail mounting. Bilateral data exchange between HDL-BUS pro bus and Ethernet / Internet
- Supports the following modes: local control, P2P control, remote control - access via the Internet to the local network and bus (default is local control)
- Allows a maximum of 4 simultaneously connected mobile devices such as tablets, smartphones or Touch Life panels.
- Supports linking to your license Iridium Mobile version SITE to use an unlimited number of mobile devices
- Consumption: 50 mA
- Module size: 78x88x66 mm
Power supply for Z-Audio SB-DN-PS1.2AD
- + 24VDC
- GND
- -24VDC
- 2A
RS-C65P column
- Power: 50W
- sensitivity: 85dB-95dB
48 Channel DMX Scene Controller with Ethernet Port SB-DN-48DMX
- Power supply: DC 24V
- Standby consumption: 40mA / DC24V
- Built-in Ethernet RJ45 interface
- Operating temperature: 0 ° C ~ 45 ° C
- Operating relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Dimensions: 144x88x66 (mm)
- Maximum 48 DMX zones
- Maximum 99 scenes in each zone, maximum scene time 60 minutes
- A maximum of 99 sequences and a maximum of 99 steps for each of them.
- The maximum interval between each step is 60 minutes.
- There are 4 modes of operation for each sequence: Forward / Back / Case / Jump
- DMX512 standard output
- DMX output HDL bus
- There is an instruction for programming and testing the module.
- Remote programming and control function
- Low, high or maximum limits are available for different types of loads on each channel
- Data switching function: between HDL bus and Ethernet
- Restores state after power on
- Interfaces: Bus HDL, RJ45, DMX512
- Can be used as an HDL bus gateway and for system programming.
Infrared Transmitter with SB-IR-EM Switch-On Detection Sensor
- Power supply: DC 24V
- Consumption: 12mA / DC24V
- Operating temperature: 0 ° C ~ 45 ° C
- Operating relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Communication Protocol: HDL Bus
- Maximum IR codes: 23
- Transmitting carrier frequency: 38 KHz
- Dimensions: 49x31x12 (mm)
- Current detection function
Relay to DIN rail to control blinds, shutters, curtains, gates and reversible loads.
SB-DN-2Motor
- Power supply: DC 24V
- Consumption: 35mA / DC24V
- Operating temperature: 0 ° C ~ 45 ° C
- Operating relative humidity: 20% ~ 90%
- Storage temperature: -40 ° C ~ + 55 ° C
- Relative storage humidity: 10% ~ 93%
- Maximum current in each channel: 5A
- Installation: standard 35mm Din-rail
- Dimensions: 72x88x66 (mm)
- 2 cross over channels of the relay for control of blinds, roller shutters, curtains, gates, etc. cross over loads
- Adjustable timer for open-close time
- It can work as a continuous relay
- Modes: Forward, Back and Stop
- Delay time is available for Forward and Backward modes.
HDL BUS
This device is configured using the HDL-BUS software package. HDL Demo Case is connected to a computer via Ethernet or the Internet. After starting the program, a registration window will appear asking you to enter the serial number and registration code, which can be obtained by sending an email to the email address indicated there.
The figure shows the starting window of the program:
Each 1-IP Switch Board is capable of processing up to 253 devices:
After starting this program, it is required to search for devices present in our device. To begin, the address (or address range) is selected. At the end of the search, you can add the necessary devices to the workspace.
After all devices are found and added to the workspace, you can configure each of them. You can also launch the settings window for the required device by pressing the corresponding menu button:
Afterword
As a result, we have a pretty good smart home system. But like everyone else, it is not without flaws. Immediately striking her great price (~ $ 2500). Program complex HDL BUS leaves much to be desired. All the study of this device was accompanied by frequent program hangs. We also could not connect to the touch screen in order to configure it (the program simply does not find it). However, I was pleased with the technical support. A couple of days after registering on the official Russian site, they called me and asked if their help was needed.
I would like to hear an objective opinion of habrayuzer on this product.
Source: https://habr.com/ru/post/241347/
All Articles