LVMOO LM028N - a mobile charger with a Wifi router

Mobile chargers, which include a Wifi router and the ability to connect a 3G modem or flash drives, began to appear on the market. LVMOO LM028N differs from other similar devices in the presence of a slot for microSD memory cards.

Specifications

Protocol support: IRRR 802.11 b / g / n; IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Wifi connection speed: 150Mbps
Security Wifi: filtering by MAC address, 64/128 bit WEP encryption, WPA / WPA2, WPA-PSK / WPA2-PSCK.
10 / 100Mbps WAN / LAN port
2 USB ports, one of which can be used to connect a 3G modem or a flash drive
SAMBA, FTP, DLNA servers
DOS attack protection, built-in firewall
Input voltage: 5V / 1A
Output voltage: 5V / 1.5A
Built-in powerbank capacity: 9600mAh

Appearance and equipment

The device comes in a small bright box with a brief listing of features at the front:


And a more detailed description behind:

Description in 2 languages: Chinese and English.
')
Inside there is a wifi router, USB cable, charger and English manual:


The instruction is very pleased, it contains a brief description of all the features:

Not lazy and made a thin manual for 30 pages. You can immediately get acquainted with all the functions and available settings simply by delivering the instructions. It is very convenient!

The router has the form of "brick" with a bright insert in the middle. There are 4 options for color inserts in the middle: yellow, green, red, blue.
I have a model with yellow color:

The device has a weight of 265 grams with dimensions of 94 x 80 x 35mm.

Below are the brief characteristics of the incoming and outgoing voltage and current, battery capacity:


Above are 5 light indicators: charge indicators 25%, 50%, 75% 100% and the indicator of the included Wifi

The functioning of the indicators at the beginning does not seem quite logical.
When charging external devices, the light is always on 100%. When the charge is exhausted, the device turns off.
You can check the charge level by holding the Charge button for a few seconds. A triple blink of 25% indicates a low charge. If the charge is sufficient, then a queue of light bulbs will light up: 25% and 50%, 25%, 50% and 75% or all 4 at once if the charge is full.
When the router is connected to the network, the bulbs from 25% to 100% will light up in turn.

On the side there is a slot for microSD cards and a Wifi lever:

yellow corner outgoing corner is an unsuccessful attempt to open the device, as a result of which the mount broke off

At the back is the RJ-45 port for a LAN connection, a USB output for charging external devices (DC-In), and a USB port for connecting a 3G modem, or external drives:


On the opposite side is the MiniUSB power input and the Reset button:

Wifi router

We translate the Wifi lever to the On state and now you can access the settings of the router through the interface.
Wifi-Router is detected as a normal access point.
The password for connecting to a Wifi router is 888888.
The web administration panel is located at http://192.168.2.1
The default username and password is admin: admin
The main menu of the administration panel consists of 3 parts:
1) Network information
2) Wifi Information
3) Information about the router


On the page to change the settings you can enter by pressing the “System Setup” button.
Information is provided in the form of 3 columns: on the left - the menu levels, in the center - settings, on the right - auxiliary information.

System Summary

In the section you can get acquainted with general information about the state of the device: information about Internet connection, usage statistics, information about connected clients.

Internet

In the section you can configure the DHCP server settings:


Perform 3G connection settings:


Configure WISP connection:

With this mode, you can configure the relay Wifi signal.
In the same section, you can configure the wired LAN connection.

Wireless

In the “Basic Settings” section, you can configure the basic settings for a Wifi router: operation mode, SSID, configure the encryption type and set its key.
Encryption types supported: WEP, WPAPSK, WPA2PSK, WPAPSK Mix


You can configure WDS:

WDS allows you to combine Wifi access points into one network, without the need for a wired connection between them.

Application

In the Application section, you can configure security settings, as well as activate access via Telnet, FTP, SAMBA.
The list of security settings is quite extensive:

• Filtering by IP / PORT
• MAC filtering
• URL filtering
• DoS protection
• Remote ping
• Remote access via WEB
• Remote telnet access
• Remote SNMP access
• FTP access
• Samba Access

Many settings for DoS protection against attacks:

It is very convenient that the detailed description of each parameter is displayed on the right.

In the same section, you can configure the routing table:


Configure access via DDNS for different providers:

With DDNS, you can access files from any computer with an Internet connection.

System

The Settings section contains settings for time settings, adding FPT accounts, SAMBA and DLNA settings, firmware update section.

Access files from Android

You can access files stored on a microSD card or USB drive and connected to a router via a SAMBA server.
To do this, in the settings of the router, you need to activate the SAMBA server (Applications section) and add a new user (System-> SAMBA section)
You need to install SAMBA-client on your smartphone. For example AndSMB
In the settings, add the IP address of the router and specify the login password for the connection.


To connect via FTP, you can use the AndFTP utility. You also need to activate the FTP server in the settings of the router and add a user.


To access via DLNA, you need to install a DLNA client. For example - Skifta . By activating the DLNA-Access on the Wifi-router you can get quick access to the media files stored on the connected drives:

Testing Powerbank

The capacity of the built-in Powerbank is declared as 9600 mAh. Let's see what is hiding inside:

And inside we have 4 banks 18650, but without labeling.

General view of the board:

At the top of the board something flooded.

Testing capacity was carried out on charging the smartphone Lenovo P780 (4000 mAh battery) and on the stand IMAX B6.
Lenovo P780 smartphone managed to charge once to 100%, the second time the charge level reached 75% and charging stopped.
At the IMAX B6 stand, we managed to get a result of about 8200 mAh (the charge was carried out in several visits).
Those. The capacity of the built-in Powerbank does not match the declared 9600 mAh.

Advantages and disadvantages

SAMBA, FTP, DLNA servers
MicroSD card slot
A printed manual describing all the possibilities.
The actual capacity of the powerbank does not match the stated

LVMOO LM028N is a very good solution for both home use and travel. Even despite the discrepancy in the claimed and real capacity of the built-in battery, they can at least 3 times charge a regular smartphone with a 2000 mAh battery.
A built-in slot for memory cards will help organize convenient storage for files accessible via SAMBA, FTP or DLNA.

In the Tinydeal.com store, a LVMOO Wifi router can be purchased for $ 47.93 using an 11% discount coupon for 8UT9XbR0KZ

If you do not have an account on Habrahabr, you can read and comment on our articles on BoxOverview.com